BRAKE PADS - We stock organic (Armstrong), Semi-sintered (Nissin NS - see picture left) and fully sintered (DP and Nissin ST - see picture left) brake pads. Organic pads are resin bonded, kind to the discs, generally quieter and fine for general road use. Sintered pads are made from metal particles put under pressure and heat, offer the best stopping power, but also cause the most rotor wear and can make the most noise. Virtually all original equipment pads are now sintered. They are also the least affected by adverse conditions and are the pad to choose for high speed and track days. Sintered pads can feel 'grabby' and may lack 'feel' at the lever. Semi-metallic pads fall right in the middle for durability and performance. A trade off between sintered and organic, they still stop well, cause less rotor wear with better lever feel than sintered metallic pads and normally make less noise.

Nissin brake pad compound chart shown left.

Rebuild kit to fit Nissin 14mm bore front brake master cylinders,

Fits: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC, Tiger 900 (carburettor model)

Rebuild kit for all Triumph (Nissin) rear brake master cylinders.

Fits America, Bonneville 800/865, T100, 600/650/675/750/900/955/1000/1200 Daytona, 750/900 Trident, 750/900/955/1050 Speed Triple, 900/1200 Trophy, Scrambler, Speed Four, Speemaster, Street Triple, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Sprint 900, Sprint Sport, Sprint Executive, Sprint ST 955/1050, Sprint GT, 955 Sprint RS, Street Triple, Tiger 800/900/955/1050, Tiger 800, Tiger XC, TT600

Fits all Nissin and Triumph front 4 piston calipers on all (Apart from Brembo) Triumph sports and touring models. Kit contains 8 seals (4 outer dust seals and 4 hydraulic seals). To equilize brake pad wear, these calipers use 2 different piston sizes, 30mm (leading) and 34mm (trailing). Use silicone or rubber grease during assembly after cleaning out any corrosion from the dust seal groove. The joint seals on the 2 halves are now also included. The piston seals are genuine Nissin parts as used as original equipment by Triumph. These seals are also used in the 1/2 Nym spec. Triumph calipers. Made in Japan.

Fits: 600/650/675/750/900/955/1000/1050/1200/2300

27mm caliper seals used on all 2 piston calipers fitted to the Triumph range. These are genuine Nissin seals. The kit contains seals to repair x 1 caliper (4 seals). When fitted correctly in a clean groove, there is a smooth action of the piston with no tying up on the dust seal. After cleaning out any corrosion in the the dust seal groove, always use silicone or rubber grease when fitting.  Made in Japan.

Fits front and rear on:

Bonneville, T100, America, Speedmaster, Scrambler, Street Cup, Street Scrambler, Thruxton,Thunderbird 900, Thunderbird Sport, Legend TT, Adventurer,Trident 750/900, Tiger 900, Tiger 955, Trident Sprint (up to VIN 9082), Trophy 900 (upto VIN 9082), Trophy 1200 (up to VIN 4901)

Fits front only on

Tiger 800, Bobber, T120,

Fits rear on

Daytona 750/900/1000/1200, Daytona T595, Daytona 955, Speed Triple 750/900, Speed Triple T509, Speed Triple 955, 1050, Speed Triple R, S, Sprint ST 955, Sprint ST 1050, Sprint RS (single sided swinging arm), Tiger Explorer, Tiger Sport, Trophy 1215, SE, Trophy 900/1200, Sprint 900, Sprint Executive, Sprint Sport

Genuine Nissin front brake reservoir plastic pot used many Triumph models. This inclues the link pipe which fits some but no all models.

Fits  TT600, Speed Four, 600/650/675/955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955/1050 Speed Triple, Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT.

Angled inlet to front brake reservoir used on most sports models. The 'O' ring seal and circlip are the same components used in the inlet to Nissin rear brake master cylinders. Genuine Nissin component. Made in Japan.

Fits TT600, Speed Four, 600/650//955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955 Speed Triple, 1050 Speed Triple (up to VIN 461331), Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT

Nissin front brake master cylinder outer boot. Fits all models with Nissin front brakes.

750/900 Trident, 600/650/750/900/955/1000/1200 Daytona, 750/900/955 Speed Triple, 900/955 Tiger, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, 900/1200 Trophy

Replacement master cylinder boot to fit all Nissin rear brake master cylinders. 

Slider pin pair of boot/covers for the 2 piston Nissin calipers.

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy (up to vin 9083), 1200 Trophy (up to vin 4902), Tiger 900, Tiger 900 (EFI), Tiger 955, Tiger 800, Tiger XC, Thunderbird 900, Legend, Thunderbird Sport, Adventurer

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger 900 (EFI), Tiger 955,  Tiger 800, Tiger XC, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster, Thunderbird 900, Thunderbird Sport, Legend, Adventurer

Rear brake master cylinder rod with a choice of 52 mm, 45 mm or 38 mm of 8 mm x 1.25 pitch thread. This will fit many models and the thread can be cut for most models to shorten to the required length. 

Thunderbird 900, Legend, Adventurer, Thunderbird Sport, T595/955/600/650 Daytona, T509/955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS, 955/1050 Tiger

x 3 rubber bleed screw covers.

Use a light coating of rubber grease when replacing brake caliper seals. Sachet contents 5g.

Brake paste, ideal for brake pad pin threads.

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore remote pot sports master cylinder.

Dark grey finish on master cylinder.

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore. Remote pot reservoir sports style master cylinder. 

Black finish on master cylinder

The 2 piston Nissin caliper used on the rear of many models and  retro front calipers. The caliper moves on slider pins when the brake is applied. The outer brake pad has a hook located in this brake pad locator nut which is screwed onto one of the slider pins. Manufactured from stainless steel. (See slider pins listed below, also in stainless steel).

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model),

Made in UK

Stainless steel replacemet pins for the 2 piston (on one side) calipers used  on the rear of most models and front of  very early Trophy, Sprint, and Trident models. The used bracket assembly is shown for reference only to help illustrate pin location.

These fit the front calipers of the following: 750/900 Trident, Tiger 900 (carburettor models), 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fits the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster

Threaded rear caliper bracket (less caliper slider pins).

Fits, Trident 750/900, Tiger 900 (carburettor), 900/1200 Trophy, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Exec...

Single banjo width Earl's stainless steel brake banjo bolt for most application where x 1 hose is fitted.

M10 x 1.25 pitch thread.

Original style copper washer 10 mm bore, 15.70 outer diameter and 1.20 mm thick. Pack size 10 pieces. Made in USA.

Plated steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder. The plating isn’t as good as original parts, but the steel is excellent and less prone to chewing up with the hex key.

Fits front and rear on 750/900 Trident, 900/1200 Trophy, 750/900/1000/595/955/1200 Daytona, 750/900/T509/955/ Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Sprint RS,

Fits front only on T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).

Stainless steel caliper piston 27 mm diameter and 31 mm long with seals for x 1 caliper (x 2 pistons and x 4 seals). These are not genuine Nissin parts.

Fits front and rear calipers on Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident, 900/955 Tiger, Bonneville, T100, Thruxton, America, Speedmaster, SE, Scrambler, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902

Fits rear caliper only on 750/900/1000/1200 Daytona, 955 Daytona (single sided swinging arm model), 750/900/955/1050 Speed Triple, 900 Sprint Sprint Sport, Sprint Executive, 955/1050 Sprint ST, Sprint RS (single sided swinging arm), Sprint GT, Tiger 1050, Tiger 1050 SE, Trophy 900 and Sprint 900 from vin 9084, Trophy 1200 from vin 4903

Fits front caliper Tiger 800, Tiger XC, Street Triple 675,

Larger 34mm diameter trailing piston used in Nissin and ''Triumph'' 4 piston type calipers. Fitted to the front of all Daytona models (up to the use of radial calipers), 900/955 Sprint, Trophy and 900/955 Speed Triples etc.  The pistons are 22.5 mm long. These are genuine Nissin pistons made in Japan.

To fit front calipers on 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955/1050 Sprint ST, RS, T509, 955 Speed Triple, T595, 955 Daytona, TT600, Speed 4, 600/650 Daytona, Rocket 3,

Nissin 4 piston calipers have 2 different size pistons to even out pad wear. This is the smaller 30mm (leading) diameter piston used on 4 piston Nissin calipers. This piston will fit all 4 piston Nissin and ''Triumph'' calipers up to the latest radial style. Piston depth 22.5 mm. This is a genuine Nissin part. Made in Japan.

Set of x 4 Nissin caliper pistons (x 2  30 mm pistons and x 2  34 mm Nymfron low friction pistons). Can be fitted to any Nissin/Triumph 4 piston caliper (not Brembo). Nissin only coat the 34 mm to reduce friction/drag. This was done to help eliminate the long lever travel problems.

Set of x 4 Nissin caliper pistons (x 2  30 mm pistons and x 2  34 mm Nymfron low friction pistons). Can be fitted to any Nissin/Triumph 4 piston caliper (not Brembo). Nissin only coat the 34 mm to reduce friction/drag. This was done to help eliminate the long lever travel problems.

Pattern caliper piston and seals to fit rear calipers on all sports twin sided swinging arm models.

Fits TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675, Street Triple, Daytona 955 (twin sided swinging arm model), Tiger 800, Tiger XC,

Brake caliper bleed screw/nipple to fit Nissin calipers used on Triumph models. Genuine Nissin part.

x 2 screw covers to fit most Nissin calipers used on retro and adventure Triumph models. These are 10mm  x 1.00 mm pitch.

Thunderbird 900, Legend, Thunderbird Sport, Adventurer, Tiger 800, Tiger 800XT, Tiger 955, Tiger 900 (injection), Bonneville range (fron calipert), Speedmaster, America, Thruxton

64mm long pad pins used on the rear of many Triumph models. These are also used on the front of all Tridents and early Trophy/Sprint models with twin piston (reaction type) calipers. This style of caliper uses 2 pins  to retain the pads. These are sold as a pair. The pad pins are genuine Nissin parts made in Japan.

Pad pins to fit all 4 piston ''Nissin'' and ''Triumph'' calipers. These are approximately 53 mm long.  x1 pin used per caliper to retain the pads, these do not project through the inside of the caliper and finish flush with the caliper body. 955 Daytona, 955 Speed Triple and 600/650 models used a longer pin with a split pin on the inside, the 53 mm long pins are fine as replacements. Sold as a pair. Genuine Nissin parts made in Japan.

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder.

Fits front and rear on:

Bobber, Bonneville T120, Daytona 750/900/1000/1200, Daytona 600/650, Daytona 675, Daytona 955 (twin sided swinging arm), Rocket III, Speed Four, 750/900 Speed Triple, Sprint 900, Sprint Executive, Sprint Sport, Sprint RS (twin sided swinging arm), Street Cup, Street Scrambler, Street Triple 675, Street Triple R, S RS, Thruxton R (liquid cooled), Tiger 800, Tiger 1050, 750/900 Trident, 900/1200 Trophy, TT600

Fits front only on:

Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple 955/1050, Sprint RS (Single sided swinging arm), Sprint ST 955/1050,

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 18 mm including 1.5 mm shoulder.

Fits front and rear on:

Adventurer, America, Bonneville, T100, Legend TT, Scrambler,  Speedmaster, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor and EFI), Tiger 955

Fits rear only on:

T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).

Nissin ST sintered pads.

Fits the front of the following: Bonneville, T100, Scrambler, Speedmaster, America, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 800, Tiger XC, Tiger 900 (injection), Tiger 955, 675 Street Triple (not R model)

Fits the rear of the following: Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 (injection), Tiger 955 (up to vin 198874)

Supplied as 2 pads for x 1 caliper

Nissin NS semi metallic front brake pads.

Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models),Tiger 955 cast wheels (from vin 198875) and Tiger 1050

Fit the front right side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901)

EBC organic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901

Nissin NS semi metallic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901